Speech timer
Last updated: 14 November 2026
Set how long the speaker has and when the two warnings should come. The display counts down in large digits, turns amber and then red at the points you chose, and keeps counting after zero so you can see how far over the speech has run.
Ready
Set the amber warning earlier than the red one, and both shorter than the target time.
In full screen: Space starts and pauses, R resets, F or Esc leaves full screen. While the timer runs the screen stays on, in browsers that support it.
How the warnings work
The timer has four states. While there is plenty of time the display is dark and reads “On time”. When the time left reaches your first warning point it turns amber and reads “Wrap up”. At the second point it turns red and reads “Finish now”. After zero it stays red, reads “Over time” and counts upwards with a plus sign, so +0:45 means the speaker is 45 seconds over.
The preset buttons set the amber warning at one fifth of the target time and the red warning at one tenth: 1:00 and 0:30 for a five-minute talk, 4:00 and 2:00 for a twenty-minute one. You can change all three times by hand. Tell the speaker before the session what each colour means. A warning helps only if the speaker knows it is coming.
How large the digits are
In full screen the time is drawn as large as the screen allows. We measured the height of one digit on three screens.
| Screen | Height of a digit | Share of screen height | Width of the time, share of screen width |
|---|---|---|---|
| Laptop, 1366 × 768 | 316 px | 41% | 70% |
| Tablet, 1024 × 768 | 294 px | 38% | 87% |
| Phone, 390 × 844 (upright) | 106 px | 13% | 82% |
On a laptop or tablet the digits fill about two fifths of the screen height. On an upright phone the width of the screen is the limit and the digits are much smaller, so turn the phone sideways if the speaker is more than a step or two away. The digits have a fixed width, so the time does not shift from side to side as the seconds change.
Colours and contrast
The speaker has to read the time at a glance, often under stage light. The table shows the contrast ratio between the digits and the background in each state. The scale runs from 1 : 1 (no difference) to 21 : 1 (black on white).
| State | Colours | Contrast ratio |
|---|---|---|
| On time | White digits on dark blue-grey | 14.07 : 1 |
| Amber warning | Dark digits on amber | 10.91 : 1 |
| Red warning and overtime | White digits on red | 6.57 : 1 |
The state is also written under the digits in words, so the signal does not depend on telling amber from red.
How accurate the clock is
The timer does not count ticks. Each time it draws the display it asks the browser’s clock how much time has passed since you pressed Start. It stays correct when the tab is in the background or the computer is busy. In our test we let it run for three minutes against the system clock: 180.2 seconds passed between the two clicks and the display read 3:00.
While the timer runs, the time is also shown in the browser tab’s title, so you can follow it from another tab. The screen stays on in browsers that support it. Your target and warning times are saved in this browser for your next visit.
Using the timer at an event
- Panels: the moderator keeps the timer on a tablet next to the question cards and resets it for each speaker. The guide to moderator cue cards covers the rest of the panel.
- Conference sessions: put a laptop on the floor at the front of the stage, or on a front-row seat, in full screen and facing the speaker.
- Rehearsals: switch on “Count up” to see how long a speech really takes, then correct the slot in your run of show.
- Planning: to find how many words fit a slot before anyone rehearses, use the speech time calculator.
Frequently asked questions
Does the timer make a sound?
No. The warnings are a change of colour and a short text under the time. A silent timer can face the speaker during a talk without disturbing the audience.
Does it keep the right time if I switch tabs?
Yes. The time is worked out from the browser’s clock, not from counted ticks, so it stays correct in a background tab. The tab title shows the time while the timer runs.
Can it count up instead of down?
Yes. Tick “Count up” to show the time used. The colour warnings still come at the same moments.
What is the longest time I can set?
599 minutes and 59 seconds, a little under ten hours.
What happens when the time runs out?
The display stays red, the text changes to “Over time” and the timer counts upwards with a plus sign until you pause or reset it.